I have some difficulty in using RealTerm Serial System. I want to use this software as GUI to communicate with PIC18F46J50 microcontroller through UART. Firstly I want to program a echo function, b. Download and install the RealTerm program. Download and copy com.rootjunky.frpbypass-1.0.apk to the device’s microSD card or internal storage Start the phone and connect it to WIFI.
Realterm Versions: Only some versions have been released on Sourceforge. Check at www.i2cchip.com/realterm for latest and other versions. Documentation is at http://realterm.sourceforge.net/ -------------------------- ChangeLog -------------------------- 2.0.0.70 Port Scanning has been completely changed for WinNT and above. WinNT+ :Ports are not scanned, they are loaded from registry to comport combobox in form '4 = VCP0'. Sorted by com number. No longer shows scanports form. The 'scanports' commandline parameter won't be needed now, as bluetooth ports don't cause delays WinME- :Scanned by opening the same as before. Please report any problems especially on old versions of Windows (pre XP eg Win98) When a port of style VCP doesn't exist, it no longer tries it as telnet port 2.0.0.69 Fix to pass quoted strings on command line through to FIRST instance No longer shows Spy driver donate dialog after driver installation. Change various send string drop downs to use TerminalHex font to display all 8 bit values added printerport driver files to dlportio.dll install section 2.0.0.68 - Interim release for Steve Mayall Mask MSB added Work begun on hexcsv formatting 2.0.0.67 Make data triggers work in stand-alone mode to make testing easier. (previously only in ActiveX mode) Improve I2C scan to use ':' to make more reliable scanning smbus devices with timeout 2.0.0.66 Fix error box from registry key reads on some systems Added HEXCSV commandline param to set the format string Change timing of scanports form display - seems to have sped up scanning 2.0.0.65 Virtual Comports (USB): Comport can be given using Key instead of the com number. The key names are in the registry list of comm devices at HKLMHARDWAREDEVICEMAPSERIALCOMM eg an I2C2PC adaptor will be VCP0, regardless of which port it is attached to Display the port registry entries on the scanports dialog... HEXCSV2DEC commandline utility added to Realterm installer HexCSV formatted display mode begun, not working yet. Add Channel to MAX127 I2C ADC control, fix rang&sign bits Add RSS news link to About box Add DataTriggerSet routine to setup trigger conditions from COM/ActX interface Remove obsolete KCDXO tab and code Splitting I2C support routines into separate unit add windowsplatform to aboutbox add INSTALL parameter for installer to use to display help, news etc after installation 2.0.0.64 Add COLOR commandline parameter to set terminal colors Caption is now also used to set the title displayed on startbar when minimised lengthen tooltip time, by request 2.5s -> 3.5s Added I2C Scan Bus function to I2C tab. Added I2C Control Register support 2.0.0.63 Add a Sync Match Counter to 'Binary Sync Chars'. -Also uses data trigger color in (yellow) TrayIcon for a few seconds add version info to aboutbox 2.0.0.62 Fix double counting of incoming chars. (disables routine associated with asc7511) Fix SPY mode not displaying char(0) Added BitBashPins box to I2CMisc tab for open drain bashing of all port pins. Added new ActiveX props: CaptureAsHex As activeX lib has changed may need to unregister and re-register Tried translate again - still errors. 2.0.0.61 Commandline parser changed (but not heavily tested) - quotes in parameters are now OK - accepts leading - or / before parameters SendStr and SendNum can be called repeatedly to push the strings into the SendString combo-boxes so they can be pre-populated 2.0.0.60 Improve Bicolor led display test routine. When port is closed by button, Terminal is enabled so scrollback continues to work Added Checksum8 and Checksum16 to Send CRC options Help commandline option now runs help 2.0.0.59 Fixed Matlab format TimeStamp values. 2.0.0.58 Added SCROLLBACK commandline parameter Fixed Scanport operation when port is specified, for quick reliable startup. - if PORT is set on command line, don't scan for ports, unless scanports also set on command line 2.0.0.57 Add new links to about box: Help forum, ChangeLog, Examples Added a button to bring up the popup menu to make it easier to find. 2.0.0.56 Seem to have fixed 'no receive chars in terminal' problem' when start up port does not exist. 2.0.0.55 Now uses FirstAvailablePort (not com1) to open. This is for laptops without COM1 Consequence is that I now do search com1-4 for 1st port if scanports=0 Hopefully will help with the terminal doesn't work problem. Temporarily added Enable Terminal button to MISC tab for debugging (didn't help) 2.0.0.54 Restore binary sync with AND and XOR fields Move HexEmulator code into separate module Add Leading Sync option, but only works for 1 char sync .... 2.0.0.53 Add Readme and Changelog to Realterm shortcuts fixed starting minimised in 2.0.0.52 Improve Scanports dialog slightly. Now brings up a message box to confirm abort scanning if too slow. 2.0.0.52 Fix for crash when using FIRST commandline parameter to send to running instance stop form flashing up when using FIRST commandline parameter to send to running instance Many more examples (installer script fixed) 2.0.0.51 Try to fix EBAUD/EFLOW not correctly activated after being set from command line 2.0.0.50 Add EFLOW commandline option Add Test button for M5451 LED display modules Add color checkbox for M5451 LED display modules 2.0.0.49 Add Send^C and Send Break items to rightclick menu Fix to cope with SCANPORTS=0 on commandline **Very ODD** ctrl+C has started working from the keyboard in the terminal. Also BREAK key sends ^C now May remove the ^C menu item in future if this is generally true. 2.0.0.48 Add PCA9545 control to I2C-2 tab to support new MUX3 pcb 2.0.0.47 Add CRC8 algorithms (smbus & dallas 1 wire) to send tab Added Telnet/Raw radio buttons for Echo port. (Changed code on main port also) Working on WaitForDataTrigger BlueSmirf on misc tab: - Fix baud rate setting command - add query baud button Clear LineError light after 1 sec. Leaves state on hint until double click on 'Error' label BaudRate setting: -Added hidden BaudMultiplier drop down to help with high baud rates on 950 uarts -trap error message during (invalid) baud rate setting to give more informative message (tested on WinXP) Update BL301 controls on I2C-2 tab for current commands Merge sboyd changes to AWASCII module. Should have no effect on Realterm. 2.0.0.46 Timestamping in capture file working (user feedback needed about perferred YMD format) Capture-as hex working statusbar toggles to show longhints disable Freeze button (until it is fixed) spinning icon extended to yellow corner for with no further data crashes (was expecting 'echo=<port>' now will accept nothing OK Change to combobox history list routine that is widely used. Should have no side-effects. 2.0.0.41 Fixes for multi-copy COM automation: Creates multiple instances instead of one single instance again (like 1.99.XX) Automation opens it with ports closed again (like 1.99.XX) Caption now 'Realterm: Automation server' for automation instances Suppresses port scanning when started as ActiveX/COM server 2.0.0.40 Added LF button to send tab 2.0.0.39 Fixed Font selector to change size and style correctly 2.0.0.38 fix to M5451 conversions so that '-1.23' doesn't light segment in digit 5 2.0.0.37 Added Float4 single-precision floating point display 2.0.0.36 Added Binary and Nibble display modes. One of these will be dropped in future version, probably 'binary' 2.0.0.35 Swapped trace and log control positions to put emphasis on log files. 2.0.0.34 Added some BlueSmirf bluetooth module commands to misc tab Changed scanports commandline option to specify last port number to scan for. This makes it easier to limit the time taken when bluetooth is present without just disabling it Add ScanPort dialog when it is taking too long. Change port scanning to scan upward to allow aborting 2.0.0.33 Indirect capture opens files for shared-reading during capture (ie capture while displaying chars in terminal) Modified AdTrmEmu.pas for this F1 key now brings up help. Update aboutbox 2.0.0.32 cleaned up activeX TLB to remove warnings Added Version property to activeX 2.0.0.31 Added controls to set Trace and log file names Added clear and dump buttons for trace/log Now capture,send correctly append to combobox tabsheet send correctly selected during send Only show Binary sync in hex modes where it is active Added active X method 'AddCannedSendString' that pushes strings into the sendstring combo boxes 2.0.0.30 Added DTR&RTS activeX fields Fixed Read Dallas1 wire ID Added PCA9544 I2C device removed translate component due to ntdll errors Added CAPDIRECT commandline and activeX hints copied into status panel 2.0.0.27 added scrollback rows field fixed commandline LFNL hack to remove 'buffer empty' error during capture. Breakss BL301 and ASC7511 reading Added 1-wire temp read button for DS1820 (untested) I2C link now sets RTS/CTS Warning in status panel about no handshaking panels swapped about attempt to use long hints in panel (not working yet) 2.0.0.26 Added CTS,DSR,DCD,Break lights to Echoport tab to enhance monitor mode. Correctly enable status lights on echo port fixed monitor assert failure in echo monitor mode 2.0.0.24 stretched Pin Description memo to fit properly 2.0.0.23 Added buttons for SPI CS pin control added and removed mod for comserv startup problem on winxp spymode bleat screen 2.0.0.21 Added Andigilog aSC7511 I2C support 2.0.0.20 Now scrollbars will appear when realterm is resized so terminal window is smaller than number of lines made ascii edit into combo-box, and added regular expansion BL301 I2C support new I2CADD command line parameter to set I2C address 2.0.0.19 Added I2C buttons to 'write then read' to make it easier to read eeproms etc. Fixed 'invert data' and char counting in ASCII emulator Char count now only counts chars from the port, and ignores chars being sent in Half duplex EOL char for Sendfile EOL delay is now LF not CR 2.0.0.18 Add humidity sensor support to I2C Misc tab Added I2CMisc tab for non-i2c chips Moved Sendfile to Capture tab to free up space on send tab commandline setting of emulator doesn't work 2.0.0.17 New installer based on NSI. Now installs fonts Colorise spy mode proper error messages when opening port no rx when port already open while opening a second instance clear terminal when changing port (w/ checkbox) paste to port/copy from port have some issues scrollback grayed unused port options F1 help launches web browser fixed bug that meant no display of control chars after switching back. (Emulator_ASCII is unused now) spy mode check that port is closed before trying to enter spy mode. Or warn changed spy mode to use teta. Works properly now fixed: first locks error (still flashes but works. fixed: capquit error active scripting examples enumerating all comports can be disabled, and run (actx control?) recieving repeated FF or FF's lost on TCP (cmdline and actx?) CAPTION doesn't work from command line... fix repeated file send and send messages sendfile delay control can go negative sendfile delay locks w/ big numbers sendfile repeats work properly exception when exiting via COM or commandline interface FLOW=3 RS485 mode can be set from command line now ------------------------------------------ Bugs ------------------------------------------ Scrollback command line option does not work. (seem to at 2.0.0 help commandline option errors when port scan is slow. Binary sync mode -doesn't seem to update correctly until after mode changed back to ascii then back to hex -perhaps should be active in ascii, but not ansi -and masking doesn't seem to work right. Check. Correct or improve explanation Freeze button no longer working. (works in 1.99.16). Code unchanged. (bug in APRO) Reported RS485 problems. Not checked, but is a known windows bug due to slow RTS timing (see apro forums) ------------------------------------------ Not really faults ------------------------------------------ showallemulator shows BS as triangle (no: ^H doesn't send BS) ----------------- ToDo .... maybe ----------------- Spy mode Capture file Installer improvements: -run it if user chooses to install -or improve installer wording so user knows to install separately -add all modified components ability to launch from com interface then detach and leave running. extend special font with larger sizes update to latest async port components, and merge my changes back to SF. RFC2217 remote port control function modbus packets, ascii? bin? CRC's -more generally add a range of checksum/crc's: CK8,CK16,ModbusAscii,ModbusCRC,CRC16,CRC32 translations command file general printer port toggle controls explicit printer port address Tidy up dlportio -add routines, merge d3 and d4 versions redundant color setting methods clean up SendString mess hex getting for I2C getstring or getline for activeX interface autosize for winxp, autosizing screen at start - doesn't seem to be needed now crc packet sync translation support autobaudrate detection scheme linedelay and chardelay are longer than supposed to be, especially for short delays Kylix version. use canned strings. (implemented from Actx, but not commandline) easy way to add i2c chip addresses. (done - AddCannedStrings) Add CRLF key eg shift+return SENDDLY commandline does not set SENDREPS=0 like documentation. As it has been commented out for reasons forgotten, I am a bit loathe to restore it. -------------------------- Feature Requests -------------------------- Spy mode capture file Resize changes rows/cols It would very useful to add command line options for font and font size choose on program start. It would be nice if the sync chars would allow random length 'Data Frames' when set to 'Single', without the data frame size speifically set. I.E. header byte set to AND $80 (MSB set) and variable length messages to follow. Delay on repeats of the Send comboboxes Key for Break and for ^C handle - and -- in commandline arguments ie -scanports=2 fix scanports to abort properly or to run in background, and to display dialog after mainform is visible. Send multiple files from command line Delays for other send options and normal terminal A 'sync feature' that will allow closing and re-opening the capture files with an incremented name. The plot files from the scope are HPGL and have a known ending sequence. So it would be nice to start the capture, and wait for the stream to come from the , including its termination set, then close the current capture file, and start a new one automatically. Later I can go in and print out the capture files directly. This would make Realterm a standalone, rather than embedding it in a second pgm.This is a package of files for using Realterm like you normally would with serial/fread/fprintf etc etc. from the instrument control toolbox. All files are prefixed 'realterm'.
rtObject = realterm(Serial Property/Value pairs)
Create a Realterm activeX control in the same manner as you would with serial(). Property/Value pairs can be in serial() format, or the native ActiveX implementation.
realtermfopen(rtObject)
Connects, creating a uniquely-named capture file for the data (used later).
realtermfopen(rtObject, captureFileName)
Same, but you specify the filename.
[captureFileID, captureFileID] = realtermfopen(...)
Returns the capture file information. Not necessary, but speeds up some of the later steps as the program won't need to fetch it every time.
realtermfclose(rtObject)
realtermfclose(rtObject, captureFileID)
Closes and cleans up
isrealterm(rtObject)
True/false if it is a valid Realterm object.
realtermfwrite(rtObject, message)
Sends a message to an rtObject.
Realterm 2.0.0.69 Download Windows 10
realtermfprintf(rtObject, input, terminator)
Wrapped version of fwrite with support for a terminator (can be anything really).
realtermfread(rtObject/fileID/filename)
realtermfread(rtObject/fileID/filename, timeOut)
realtermfread(rtObject/fileID/filename, timeOut, maxCharacters)
realtermfread(rtObject/fileID/filename, timeOut, maxCharacters, precision)
Reads out from the rtObject. Inputs are similar to fread, but the first argument can be the rtObject, the capture file ID, or the capture filename. Default timeout (if unspecified or empty) is 5 seconds. maxCharacters is the maximum number of characters to read out. Precision is as in fwrite - the default is 'uchar'
realtermfscanf(rtObject/fileID/fileName, terminator, timeOut, outputFormat, maxCharacters)
The minimum number of inputs is the rtObject and the terminator. The default timeout is 5 seconds, and the output format is the same as in sscanf - a C language conversion specifier (can be empty to apply nothing). The maxCharacters is the maximum number of characters to be read out.
When reading information, the priority is the same as for serial commands, i.e. it will try to read the number of characters specified, OR up to the terminator, but will timeout if it takes too long.
bytesAvailable = realtermbytesavailable(rtObject/fileID/filename)
Returns the remaining bytes left to read out (comparable as get(serialObject, 'BytesAvailable')). Also doubles up as an improved version of feof (it doesn't update in MATLAB immediately if an external program is writing to a file, as Realterm would).
Enclosed are also:
fid = realtermfid(rtObject)
Returns the file ID for the capture file from rtObject.
fid = getfid(filename)
Returns the fid(s) for filenames in MATLAB. Filename can be a string, in which case fid is a 0xn array of file ids. If filename is a cell array of strings, then it returns a cell array of fids. If the file is not open, it returns [].
filename = createuniquefile(stem)
Generates a unique temporary filename from a supplied (optional) string stem.
Realterm Serial Capture Program
rtObject = realtermserial(serialObject)
Returns an rtObject, using the existing serial object as a template for the configuration. The serial object cannot be connected.
Real Term Serial Capture Program 2.0.0.70 Download
tf = ispv(Property/Value pairs)
Checks that a set of property/value pairs is valid.